Abstract en anglais : "The interconnection between engineering simulations, real-world experiments, and virtual reality remains underutilised in engineering. This study addresses this gap by implementing such interconnections, focusing on active thermography for a carbon fibre plate in the aerospace domain. Six scenarios based on three parameters were simulated using ComSol Multiphysics 6.2 and ...

Abstract en anglais : "Material Extrusion (MEX), particularly Fused Filament Fabrication (FFF), is the most widespread among the additive manufacturing (AM) technologies. To further its development, understanding the influence of the various printing parameters on the manufactured parts is required. The effects of varying the infill percentage, the number of layers of the top and bottom surfaces ...

Abstract en anglais : "When considering the replacement of fossil fuels, hydrogen emerges as a promising clean fuel alternative. However, significant challenges arise when attempting to store it in its gaseous state. To accommodate a substantial mass of hydrogen, storage necessitates high pressures. Desired characteristics for hydrogen storage tanks include high tensile strength, low density, ...

Abstract : "This paper deals with the numerical modelling of non-destructive testing of composite parts using active thermography. This method has emerged as a new approach for performing non-destructive testing (NDT) on continuous carbon fibre reinforced thermoplastic polymer (CCFRTP) components, particularly in view of detecting porosity or delamination. In this context, our numerical model has ...

Abstract ; "Nowadays, the additive manufacturing of multifunctional materials is booming. The fused deposition modeling (FDM) process is widely used thanks to the ease with which multimaterial parts can be printed. The main limitation of this process is the mechanical properties of the parts obtained. New continuous-fiber FDM printers significantly improve mechanical properties. Another limitation ...

Abstract : "The innovative Green Ceramic Hybrid Machining (GCHM) process sequentially combines milling with a cutting tool (GCM, Green Ceramic Machining) and laser beam machining (GCLBM) of a ceramic material (black Y-TZP in this study) at the green stage mainly to increase productivity, avoid taper angle limitations of laser beam machining, and obtain micro-features. The study focuses on ...

"This paper proposes a portable 3D printed test set-up allowing to realize this transient measurement while ensuring no interaction with the outside world. Moreover the setup proposes a variation of distance to favor or not the interaction of the semiconductor with the ionizing radiation source. The main advantages of the proposed 3D setup is its adaptability to any kind of radiation source geometry ...

"The invention relates to an apparatus configured to detect and measure in real time an electrical response from an electrical component exposed to ionizing radiation." Participation d'un chercheur de la HEPH-Condorcet mais le brevet est déposé par l'UMons : https://orbi.umons.ac.be/handle/20.500.12907/45680

"In this article, dimensional and geometrical performances of two Fused Deposition Modelling (FDM) printers with Cartesian architecture (Ultimaker S3 and Intamsys FUNMAT HT) are compared using an original benchmark artifact design. Five parts were printed on each printer in ABS. Five other parts were also produced with the Ultimaker S3 in PLA to show the influence of material choice on the printer’s ...

"Standards enabling the objective tolerancing and evaluation of dimensional and geometrical performances of additive manufacturing (AM) printers are still missing. The design, printing and measurements of geometrical benchmark test artefacts (GBTA) is the current solution proposed in literature. However, the current GBTA with fixed dimensions cannot cover most of the available printing area of ...

"The micro manufacturing of ceramic components is technologically challenging especially when complex shapes and micro features are required. A hybrid manufacturing chain is developed for non-sintered(green) blanks machined using sequentially a cutting tool and a laser source. During the preparation of the green blank, a binder is added to the powder to improve compaction. The amount of binder can ...

Abstract : "Manufacturing of advanced ceramic parts exhibiting complex geometries is laborious and expensive. Traditionally, the machining is carried out on a so-called ‘green ceramic’: a compact composed of ceramic powder held with the help of a binder. This difficulty is due not only to the composition of the material, but also to the lack of methods that determine optimal machining parameters. ...

" This article aims to make a review of the existing benchmark artifacts and to summarize the main requirements chosen by authors. From this state of the art, a new benchmark artifact is proposed by adapting an existing one to fulfil its missing characteristics. Measurements possibilities in terms of dimensions are enumerated and organized using ISO 286 dimensional intervals as presented in the ...

Contribution to ESAFORM2021. Abstract : "When modelling a cutting operation, the constitutive model of the machined material is one of the key parameters to obtain accurate and realistic results. Up to now, the Johnson-Cook model is still the most used, even if an increasing number of models, such as the Hyperbolic TANgent (TANH) model, were introduced last years to overcome its limitations and ...

Abstract : "The number of FabLabs has been steadily increasing over the last few years. Their main objectives are to sensitize its public on Science, Technology, Engineering, and Math (STEM) education through the digital manufacturing chain of an object and to allow the large public to make their own objects. Through, the increasing popularization of these advanced technologies, it becomes more ...

Abstract : "Yttrium oxide tetragonal zirconia polycrystals (Y-TZP) is an inert bioceramic used for many bio-implantable applications that request a high accuracy which is difficult to achieve with the current technologies. Laser machining of hard ceramic is difficult because the interaction of the laser beam with the material can lead to microcracks and surface modifications of the microstructure. ...

Contribution to euspen’s 20th International Conference & Exhibition (Geneva, CH, June 2020) Abstract : "The ceramic microcomponents have very interesting mechanical and thermal properties in an extreme environment such as a high temperature, a corrosive environment, etc. Unfortunately, the principal limitation of ceramic material usage is its shaping because of the brittlness of the material. ...

Abstract : "The demand for inert bioceramics is always increasing in the dental field. Yttrium oxide tetragonal zirconia polycrystals (Y-TZP) are oxide ceramics which are currently used because of their interesting mechanical properties due to a toughening transformation. Industrially speaking, machining of the ceramic before sintering (green body) is very common because it allows a better productivity ...

Abstract : "Laser beam machining of Y-TZP engineering ceramic material is carried out in green stage to increase the material removal rate. The generation of hot spots may cause local sintering of the ceramic material leading to a decrease of the mechanical properties of the final sintered component. This paper presents the implementation of alternative laser beam paths to reduce the hot spots ...

"Additive manufacturing is feeding great hopes for future developments in fields such as aeronautical, biomedical and rapid tooling industrssssies. However, limitations are still restricting its use to make prototypes and hampering mass production. In the case of titanium alloy printing (e.g. Ti6Al4V) with the EBM (Electron Beam Melting) process, the major obstacle to use parts directly after printing ...